Troubleshooting Gasket Failure


HomeHome / News / Troubleshooting Gasket Failure

May 30, 2023

Troubleshooting Gasket Failure

In the oil, gas and process industry, engineers and technicians must face the

In the oil, gas and process industry, engineers and technicians must face the problem of maintaining a hermetic seal for a variety of industrial equipment. An example is flanges, which are the most common attachment method of one pipe to another pipe or equipment. Since the parts to be jointed are both rigid, they both must be perfectly machined and aligned. They also must maintain this aligned position during changing service conditions in order to maintain a seal. This can be difficult to achieve given the nature of alloys used in equipment, the fluids to be contained, as well as process variables (such as vibration, temperature variations, wear and chemical compatibility) and cost constraints (man-hour maintenance time, cost of products and downtimes).

This is why gaskets are crucial. A gasket is intended to fill the gap between two mating components, generally softer than the rigid parts to be joined, and to prevent the loss of fluid in the form of leakage. A seal is achieved by compressing the joined objects and the gasket, making the latter fill the irregularities of flange surfaces by interacting with the clamping forces and internal pressure.

Pipes are not empty. They have fluid flowing through them and through the flanges. Any fluid has the property to extend force in all directions. Initially, the fluid contained through the pipeline will come in contact to the surface of the internal diameter of the flange and also the gasket. The amount of force can be calculated using Equation 1.

Gaskets will seal given the initial amount of force applied to them. Gasket manufacturers and design engineers have determined that by torqueing the bolts used to compress the flanges, the gasket can be compressed. The simplest model for this is Equation 2 relating applied compressive force to bolt torque.

However, the stress to which the gasket is subjected is not uniformly proportional to the bolt torqueing value because the stress can vary circumferentially. This is because the contact pattern and the area between the gaskets and the flange faces is different from the contact area of the bolts and nuts. The total force applied to the flange by bolting is shown in Equation 3.

The torque proportional to a given number of bolts n, is shown in Equation 4.

Expressing T as the torque in foot-pounds, this is the primary means of force applied by user to the gasket to prevent leakage.

Though the equations presented here are ideal models (since they do not consider rugosity, other flange forces resisting, etc.), they do represent average observed conditions in industry. As shown in Table 1, the applied force through bolt tightening compresses the gasket, deforming it.

This applied force must overcome the fluid's pressure (hydrostatic force) if leakage is to be avoided. The hydrostatic force in the pipeline tends to separate the flanges and acts against the compressive bolting force, reducing it during operation.

The gasket must be both strong enough to withstand process pressure and soft enough and deformable to fill the irregularities of the flanges. Though several papers have been written to provide a better understanding of the relationship between gaskets and flanges, it is commonly known that the sealing capability is not only achieved by bolting, but rather by a combination of factors that may vary from one kind of joint to another.

Piping induced forces come into play soon after installation. During operation they begin affecting the system due to temperature and process influence on the pipe material and configuration.

Nuts and fasteners are the other key elements in providing compressive pressure on the flanges and gaskets. Their function is to clamp the joint sufficiently, given the induced tension due to process variables. Fasteners also exhibit relaxation and elongation that is dependent to their material of construction, having a considerable effect on the amount of load available.

If the elastic region for a fastener is exceeded during operation, the fasteners will yield and be irreversibly deformed, and the ability to provide a load force—essentially a compression load—will be reduced.

Vibration, alignment and mechanical flexibility affect the amount and extent of these deformations, making them key equipment and process design variables to take into account under variable operating conditions.

If the gasket copes with all of these forces by bolt torqueing, four scenarios can occur depending on the applied stress:

Gasket stress is adequate to withstand internal forces and flange forces, achieving good sealing performance.

Gasket stress drops to the point that it is insufficient to compensate for flange forces.

Gasket stress is too high and quickly compromises the integrity.

Piping induced forces/flange forces increase to a value that compromises integrity of both the gasket and the piping system/equipment.

Gasket properties also come into play in any of these scenarios. Knowing the gasket material, density, compressibility, recovery, relaxation, minimum seating stress and minimum stress under operation is essential to establish limits on assembly bolt stresses for which the gasket achieves contact and seals.

Thus, premature or catastrophic failure in the pipeline can result from low torqueing loads, inadequate gasket selection, inadequate installation practices, bad selection of materials or even poor equipment design.

Gasket manufacturers and technicians have used their years of experience to come up with troubleshooting guides and rules of thumb to assist users with the best solution for their own particular situation.

Recommendations are available through gasket manufacturers for any specific set of process variables.

Gaskets, joints, fasteners and process variables should be seen as a whole dynamic system rather than lesser isolated elements to be controlled.

In that way, the investigative process of gasket failure ensures that leakage problems can be accurately targeted by the actual cause and its implications in process dynamics.

References1. Kobayashi, Takashi "Study on the Deflection of Gaskets and Its Effects on Residual Bolt Forces and Tightness of Bolted Flanged Connections" ASME 2014 Pressure Vessels & Piping Conference. PVP2014-28514

Next Month: Isolation of Noise and Vibration in HVAC and Plumbing Piping Systems – Why Rubber is the Best Choice

We invite your suggestions for article topics as well as questions on sealing issues so we can better respond to the needs of the industry. Please direct your suggestions and questions to [email protected].

Guillermo San Martín studied chemical engineering and graduated from the University of the State of Mexico. He is currently head of engineering and development of Empak Spirotallic Mexicana.